Plumbing for Beginners: The Essentials for Installing a Bathtub
Plumbing for Beginners: The Essentials for Installing a Bathtub
Blog Article
Everyone will have their private beliefs in relation to Installing A Bathtub.
Mounting a bath tub isn't precisely rocket science, however it does call for solid plumbing, carpentry, and also in some cases, tiling abilities. Changing an old tub with a brand-new one is likewise a moderately tough task. If the old bathtub is conveniently obtainable, the project can relocate immediately; if you need to open a wall surface to remove the old bathtub and also position the new bath tub, the task is much harder. In either situation, the job is within a residence handyman's skills, although you will need an assistant to move out the old tub as well as set in the brand-new one. Make certain you have actually certified yourself for the work and are comfortable attempting it. Rather than working with a specialist to take control of a halfway-completed project, it is better to take into consideration using one prior to you start. Possibilities are you may require a specialist plumber to make tube links.
This short article will aid you install a new tub in your restroom if you have actually already bought a brand-new bathtub as well as do not need to alter the setup of your previous water supply pipes.
Your devices as well as material checklist ought to comprise the following:
Removing Old Taps
If you need to replace old faucets with new ones as a part of your installation, after that the first thing you should do is detach the water system. After doing so, turn on the taps to drain any type of water continuing to be in the system. The process of getting rid of the existing faucets can be rather troublesome as a result of the limited accessibility that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a towel prepared for the staying water that will certainly come from the pipelines. When the supply pipes have actually been gotten rid of, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from turning throughout this process. Once the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned up of any old securing compound.
Prior to moving on to fit the brand-new taps, compare the pipe connections on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to avoid damages to the string. One end of the port fits on the plastic tail of the tap and the other end supplies a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly need minimizing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the placing opening in the bath/basin guaranteeing that the washers are in location between the faucet and also the sink. Safeguard the faucet in place with the producer supplied backnut. When the faucet is safely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with typical tap ports. The previous kind should be connected to the faucet ends initially, tightening only by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Bathtub
Making use of the two wood boards under its feet, put the bathtub in the required position. The wood boards are useful in uniformly spreading the weight of the tub over the area of the boards instead of concentrating all the weight onto four little factors.
The next goal is to make sure that the tub is leveled all round. This can be attained by inspecting the level as well as readjusting the feet on the tub until the spirit level checks out level.
To mount faucets, fit the bottom of the outermost flexible faucet adapter to the suitable supply pipeline by making a compression sign up with; after that do the very same for the various other tap.
Switch on the supply of water and check all joints and new pipework for leaks and tighten them if required. Fill the bath tub and likewise examine the overflow outlet as well as the regular outlet for leaks.
Lastly, deal with the bath paneling as explained in the supplier's instruction manual. Tiling and securing around the bath tub ought to wait until the bathtub has been made use of at the very least once as this will certainly resolve it into its last position.
Getting ready for the Setup
Firstly, the sustaining structure supplied with the bath needs to be fitted (if required) according to the producer's directions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is important to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets unit to prevent strain on the tub.
Fit the versatile tap adapters to the bottom of the two taps utilizing 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath need to currently be ready to be suited its final position.
Tiling Around the Tub
In the area where the bath meets the ceramic tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to break a rigid seal, triggering the water to permeate the wall in between the bath and the tiling, bring about problems with moisture and also possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your fixtures as well as fittings. They are sold in tubes and also cartridges, as well as can sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to always load the tub with water prior to securing, to allow for the motion experienced when the tub remains in usage. The sealer can fracture relatively very early if you do not consider this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally quickly available on the marketplace. It is suggested to fit the floor tiles utilizing waterproof or water-proof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed reading our article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thank you for taking a few minutes to read our content. Sharing is caring. Helping people is fun. Thanks so much for going through it.
Trusted service? Dial! Report this page